Arc behaviour and metal transfer of the VP-GMAW process

This project evaluated the metal transfer behaviour of the variable polarity (VP) GMAW process. Analysis was performed using high speed video that was synchronised with high speed data acquisition. Melting rate measurements were found to be very dependent on current waveform, polarity, and droplet size, and metal transfer if it occurred, for each waveform period. The transient conditions of current waveform and metal transfer produced rapid changes in arc behaviour which influenced the melting at the electrode tip and growing droplet. The concentrated melting theory was developed to explain the significant increase in electrode extension burnoff and droplet growth rate that occurred at short EN time as a function of current, and during EP peak pulse when the pre-pulse droplet volume was small. The highest electrode extension burnoff and droplet growth rate occurred when the arc was permitted to climb over the solid electrode tip producing rapid concentrated melting. Likewise, large molten droplets were found to promote a negative electrode extension burnoff and a decreased droplet growth rate. The arc rooted on large droplets providing additional heating but limited electrode melting. The droplet burnoff rate (DBR) method was developed and found to yield good experimental measurements for the arc and resistive heating coefficients used in a 2nd order melting rate equation developed for a complex waveform process, like VP-GMAW. For the EN period, the EN time affected the melting rate as a function of EN current. The greater melting rate that occurred at low EN time was measured by the changes in the resistive heating coefficient. Concentrated arc melting of the electrode extension at low EN time caused the slope of the burnoff diagram to increase, which represented the resistive heating coefficient. The melting rate of the EP pulse was related to the pre-pulse droplet volume. Large pre-pulse droplets decreased the arc heating coefficient, which could be negative, which meant the electrode extension was increasing and the arc length was decreasing in that waveform period. VP-GMAW power supplies offered stable operation for welding sheet structures on both carbon steel and stainless steel. Higher travel speeds were required as the %EN of the waveform increased to produce acceptable constant deposit area fusion. Welding speeds were up to 300% higher with VP-GMAW compared to the GMAW-P process when welding lap joints on 1.8 mm thick material with a 1.8 mm gap. VP-GMAW heat input was up to 47% less than GMAW-P for the same melting rate

Reduced heat input keyhole welding through improved joint design

An improved high energy density welding method for reducing input keyhole welding prepares the weld joint (8) between two edges (10, 14) of at least one member by separating the edges (10, 14) of the member (12, 16) with a controllable gap (22) by a projecting portion (24) selectively positioned on one edge (10, 14) of the member (12, 16). The projecting portion (24) closely abuts the other edge of the member for maintaining the controlled distance (d) of the controllable gap (22) to enhance the welding method

Method for defect free keyhole plasma arc welding

A plasma arc welding process for welding metal of increased thickness with one pass includes operating the plasma arc welding apparatus at a selected plasma gas flow rate, travel speed and arc current, to form a weld having a penetration ratio to weld height to weld width, and maintaining the penetration ratio at less than 0.74. Parameters for the plasma gas flow rate, travel speed and arc current are adjusted to a steady state condition during a start up period and maintained during the steady state condition to complete a weld. During a terminal stopping period, the travel speed is stopped and instantaneously replaced by filler wire which adds material to fill the keyhole that had been formed by the welding process. Parameters are subsequently adjusted during the stopping period to terminate the weld in a sound manner

Conversion of the Mycotoxin Patulin to the Less Toxic Desoxypatulinic Acid by the Biocontrol Yeast Rhodosporidium kratochvilovae Strain LS11

Se describe en este artículo el descubrimiento de la degradación de la micotoxina patulina por una levaduraThe infection of stored apples by the fungus Penicillium expansum causes the contamination of fruits and fruit-derived products with the mycotoxin patulin, which is a major issue in food safety. Fungal attack can be prevented by beneficial microorganisms, so-called biocontrol agents. Previous time-course thin layer chromatography analyses showed that the aerobic incubation of patulin with the biocontrol yeast Rhodosporidium kratochvilovae strain LS11 leads to the disappearance of the mycotoxin spot and the parallel emergence of two new spots, one of which disappears over time. In this work, we analyzed the biodegradation of patulin effected by LS11 through HPLC. The more stable of the two compounds was purified and characterized by nuclear magnetic resonance as desoxypatulinic acid, whose formation was also quantitated in patulin degradation experiments. After R. kratochvilovae LS11 had been incubated in the presence of 13C-labeled patulin, label was traced to desoxypatulinic acid, thus proving that this compound derives from the metabolization of patulin by the yeast. Desoxypatulinic acid was much less toxic than patulin to human lymphocytes and, in contrast to patulin, did not react in vitro with the thiol-bearing tripeptide glutathione. The lower toxicity of desoxypatulinic acid is proposed to be a consequence of the hydrolysis of the lactone ring and the loss of functional groups that react with thiol groups. The formation of desoxypatulinic acid from patulin represents a novel biodegradation pathway that is also a detoxification process

Determining the Orientation of Protegrin-1 in DLPC Bilayers Using an Implicit Solvent-Membrane Model

Continuum models that describe the effects of solvent and biological membrane molecules on the structure and behavior of antimicrobial peptides, holds a promise to improve our understanding of the mechanisms of antimicrobial action of these peptides. In such methods, a lipid bilayer model membrane is implicitly represented by multiple layers of relatively low dielectric constant embedded in a high dielectric aqueous solvent, while an antimicrobial peptide is accounted for by a dielectric cavity with fixed partial charge at the center of each one of its atoms. In the present work, we investigate the ability of continuum approaches to predict the most probable orientation of the β-hairpin antimicrobial peptide Protegrin-1 (PG-1) in DLPC lipid bilayers by calculating the difference in the transfer free energy from an aqueous environment to a membrane-water environment for multiple orientations. The transfer free energy is computed as a sum of two terms; polar/electrostatic and non-polar. They both include energetic and entropic contributions to the free energy. We numerically solve the Poisson-Boltzmann equation to calculate the electrostatic contribution to the transfer free energy, while the non-polar contribution to the free energy is approximated using a linear solvent accessible surface area relationships. The most probable orientation of PG-1 is that with the lowest relative transfer free energy. Our simulation results indicate that PG-1 assumes an oblique orientation in DLPC lipid bilayers. The predicted most favorable orientation was with a tilt angle of 19°, which is in qualitative agreement with the experimentally observed orientations derived from solid-state NMR data

Binding of protegrin-1 to Pseudomonas aeruginosa and Burkholderia cepacia

BACKGROUND: Pseudomonas aeruginosa and Burkholderia cepacia infections of cystic fibrosis patients' lungs are often resistant to conventional antibiotic therapy. Protegrins are antimicrobial peptides with potent activity against many bacteria, including P. aeruginosa. The present study evaluates the correlation between protegrin-1 (PG-1) sensitivity/resistance and protegrin binding in P. aeruginosa and B. cepacia. METHODS: The PG-1 sensitivity/resistance and PG-1 binding properties of P. aeruginosa and B. cepacia were assessed using radial diffusion assays, radioiodinated PG-1, and surface plasmon resonance (BiaCore). RESULTS: The six P. aeruginosa strains examined were very sensitive to PG-1, exhibiting minimal active concentrations from 0.0625–0.5 μg/ml in radial diffusion assays. In contrast, all five B. cepacia strains examined were greater than 10-fold to 100-fold more resistant, with minimal active concentrations ranging from 6–10 μg/ml. When incubated with a radioiodinated variant of PG-1, a sensitive P. aeruginosa strain bound considerably more protegrin molecules per cell than a resistant B. cepacia strain. Binding/diffusion and surface plasmon resonance assays revealed that isolated lipopolysaccharide (LPS) and lipid A from the sensitive P. aeruginosa strains bound PG-1 more effectively than LPS and lipid A from resistant B. cepacia strains. CONCLUSION: These findings support the hypothesis that the relative resistance of B. cepacia to protegrin is due to a reduced number of PG-1 binding sites on the lipid A moiety of its LPS

Two Major Medicinal Honeys Have Different Mechanisms of Bactericidal Activity

Honey is increasingly valued for its antibacterial activity, but knowledge regarding the mechanism of action is still incomplete. We assessed the bactericidal activity and mechanism of action of Revamil® source (RS) honey and manuka honey, the sources of two major medical-grade honeys. RS honey killed Bacillus subtilis, Escherichia coli and Pseudomonas aeruginosa within 2 hours, whereas manuka honey had such rapid activity only against B. subtilis. After 24 hours of incubation, both honeys killed all tested bacteria, including methicillin-resistant Staphylococcus aureus, but manuka honey retained activity up to higher dilutions than RS honey. Bee defensin-1 and H2O2 were the major factors involved in rapid bactericidal activity of RS honey. These factors were absent in manuka honey, but this honey contained 44-fold higher concentrations of methylglyoxal than RS honey. Methylglyoxal was a major bactericidal factor in manuka honey, but after neutralization of this compound manuka honey retained bactericidal activity due to several unknown factors. RS and manuka honey have highly distinct compositions of bactericidal factors, resulting in large differences in bactericidal activity

Isostructural second-order phase transition of b-Bi2O3 at high pressures: an experimental and theoretical study

This document is the Accepted Manuscript version of a Published Work that appeared in final form in Journal of Physical Chemistry C, copyright © American Chemical Society after peer review and technical editing by the publisher. To access the final edited and published work see http://dx.doi.org/10.1021/jp507826jWe report a joint experimental and theoretical study of the structural and vibrational properties of synthetic sphaerobismoite (beta-Bi2O3) at high pressures in which room-temperature angle-dispersive X-ray diffraction (XRD) and Raman scattering measurements have been complemented with ab initio total energy and lattice dynamics calculations. Striking changes in Raman spectra were observed around 2 GPa, whereas X-ray diffraction measurements evidence no change in the tetragonal symmetry of the compound up to 20 GPa; however, a significant change exists in the compressibility when increasing pressure above 2 GPa. These features have been understood by means of theoretical calculations, which show that beta-Bi2O3 undergoes a pressure-induced isostructural phase transition near 2 GPa. In the new isostructural beta' phase, the Bi3+ and O2- environments become more regular than those in the original beta phase because of the strong decrease in the activity of the lone electron pair of Bi above 2 GPa. Raman measurements and theoretical calculations provide evidence of the second-order nature of the pressure-induced isostructural transition. Above 20 GPa, XRD measurements suggest a partial amorphization of the sample despite Raman measurements still show weak peaks, probably related to a new unknown phase which remains up to 27 GPa. On pressure release, XRD patterns and Raman spectra below 2 GPa correspond to elemental Bi-I, thus evidencing a pressure-induced decomposition of the sample during downstroke.Financial support from the Spanish Consolider Ingenio 2010 Program (MALTA Project CSD2007-00045) is acknowledged. This work was also supported by Brazilian Conselho Nacional de Desenvolvimento Cientifico e Tecnologico (CNPq) under Project 201050/2012-9, Spanish MICINN under Projects MAT2010-21270-004-01/03/04 and MAT2013-46649-C4-2/3/4-P, Spanish MINECO under Project CTQ2012-36253-C03-02, and from Vicerrectorado de Investigacion de la Universitat Politecnica de Valencia under Projects UPV2011-0914 PAID-05-11 and UPV2011-0966 PAID-06-11. Supercomputer time has been provided by the Red Espanola de Supercomputacion (RES) and the MALTA cluster. JAS. acknowledges Juan de la Cierva fellowship program for financial support.Pereira, ALJ.; Sans Tresserras, JÁ.; Vilaplana Cerda, RI.; Gomis, O.; Manjón Herrera, FJ.; Rodriguez-Hernandez, P.; Muñoz, A.... (2014). Isostructural second-order phase transition of b-Bi2O3 at high pressures: an experimental and theoretical study. Journal of Physical Chemistry C. 118(40):23189-23201. https://doi.org/10.1021/jp507826jS23189232011184

Optimization of the doxycycline-dependent simian immunodeficiency virus through in vitro evolution

<p>Abstract</p> <p>Background</p> <p>Vaccination of macaques with live attenuated simian immunodeficiency virus (SIV) provides significant protection against the wild-type virus. The use of a live attenuated human immunodeficiency virus (HIV) as AIDS vaccine in humans is however considered unsafe because of the risk that the attenuated virus may accumulate genetic changes during persistence and evolve to a pathogenic variant. We earlier presented a conditionally live HIV-1 variant that replicates exclusively in the presence of doxycycline (dox). Replication of this vaccine strain can be limited to the time that is needed to provide full protection through transient dox administration. Since the effectiveness and safety of such a conditionally live virus vaccine should be tested in macaques, we constructed a similar dox-dependent SIV variant. The Tat-TAR transcription control mechanism in this virus was inactivated through mutation and functionally replaced by the dox-inducible Tet-On regulatory system. This SIV-rtTA variant replicated in a dox-dependent manner in T cell lines, but not as efficiently as the parental SIVmac239 strain. Since macaque studies will likely require an efficiently replicating variant, we set out to optimize SIV-rtTA through in vitro viral evolution.</p> <p>Results</p> <p>Upon long-term culturing of SIV-rtTA, additional nucleotide substitutions were observed in TAR that affect the structure of this RNA element but that do not restore Tat binding. We demonstrate that the bulge and loop mutations that we had introduced in the TAR element of SIV-rtTA to inactivate the Tat-TAR mechanism, shifted the equilibrium between two alternative conformations of TAR. The additional TAR mutations observed in the evolved variants partially or completely restored this equilibrium, which suggests that the balance between the two TAR conformations is important for efficient viral replication. Moreover, SIV-rtTA acquired mutations in the U3 promoter region. We demonstrate that these TAR and U3 changes improve viral replication in T-cell lines and macaque peripheral blood mononuclear cells (PBMC) but do not affect dox-control.</p> <p>Conclusion</p> <p>The dox-dependent SIV-rtTA variant was optimized by viral evolution, yielding variants that can be used to test the conditionally live virus vaccine approach and as a tool in SIV biology studies and vaccine research.</p